• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with a keyless entry system built into. This key typically resembles the remote control and can be replaced with a fresh one from an 2011 kia soul key fob programming dealer or a locksmith.

Key fobs are prone to malfunction for several reasons, including a dead coin battery, worn buttons signal interference, water damage, and a defective receiver module. Here are some helpful tips to help you get your kia sportage key replacement key fob that is a replacement for the sportage for good.

How to replace the remote key or smart key?

It doesn't matter if your Kia comes with an intelligent key, remote key push to start key or a standard non-transponder key made of metal the battery in these keys will eventually need replacing. This is particularly relevant if your vehicle displays a message that indicates that the smart key or remote has low battery power.

It's a simple procedure. To replace the battery in the key fob take the mechanical key from the slit at the back of the key fob. Next, pry open the cover. Inside the key fob, there will be tiny screws that hold the battery in place. By using a small screwdriver remove the screw and pull out the old battery. Install the new battery and close the opening on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go if the doors lock and unlock as you expect. You can now use the hands-free lock/unlock feature on your Kia when your fingers are cold or you need to go on errands around Brandon.

Note: Some key fobs may need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) do not require programming. If you're looking to reprogramme your key, you'll have to write down the key code's number on the key code tag.

How to replace the battery

If the Kia key fob does not respond to pressing the lock or unlock button, it's likely that the battery is not fully charged. A battery that is not functioning properly could cause other issues such as the check engine light coming on or the engine not cranking. Fortunately replacing the battery on the key fob is a simple DIY task that requires only the most basic tools.

Before beginning the process be sure that your vehicle is off and all doors are shut. Locate the small metal or plastic piece at the bottom of your key fob, and move it until a metal key pops out. You can then insert this key into the door handle of the driver to unlock your car.

To replace the key fob battery, remove the cover from the back and use a plastic pry bar tool to release the latch holding the black negative battery cable. Remove the old battery and align the new battery so that the "+" positive side is facing you, and the "-" negative side is facing the fob's metallic electrical contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid damaging or breaking the contacts made of metal.

Once the new battery has been installed and the key fob is turned on, turn it off and back on in the ignition repeatedly until the door locks cycle. You can then test the Kia's key fob to ensure it is working correctly.

How to replace a smart keys

Depending on the model of your 2018 kia sportage replacement key Sportage, you may have the standard key fob, or a smart key. The difference between these is that the smart key has the small blade of a key hidden within it, whereas the standard fob doesn't. Both key fobs contain an internal battery that will eventually require replacing. Fortunately, this is a fairly simple process that takes only two minutes.

Make sure you turn off your Kia and sit on a level and well-lit surface prior to you begin. Keep in mind that the fob is made up of tiny pieces that could fall in the event of a mishap.

The small release button is located on the lower backside. It's either a circular button or rectangular slot. Once you press this, the mechanical key blade will come out and you can then open the key fob.

Once you have the key fob open it is easy to take off the old battery and replace it. The new battery should be a CR-2032, and can be purchased online or at your local auto parts store. After you've finished, your key fob should be able to lock or unlock and start your vehicle, even if it isn't running.

How to replace a mechanical key

The Kia Replacement fob key fob is a wonderful option that lets us lock and unlock our car at the click of the button. Like all devices like a key fob, the Kia might have issues. There are solutions to resolve these issues and keep your key fobs in good working order for a long time.

A dead or weak battery is among the most common problems. This could cause the fob to cease working or to work intermittently. If this is what you are experiencing you should replace the battery an entirely new battery.

If this doesn't fix the problem you can try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a brand new one.

Once the new battery is in, close and then open the doors with the mechanical key (every kia picanto key fob programming fob has an emergency mechanical key that can fit in the slot). Test the key fob to confirm it's functioning correctly. Contact a dealer or locksmith to address the issue when the fob still is not working. Make sure they cut you an emergency key that works for all trunk and door cylinders to avoid future lockouts.