• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat punto car key 500 Key Fob Won't Work

A key fob from fiat 500 stolen without keys 500 is a convenient way how To get fiat key code unlock the doors and start the car. There are many reasons why the fob won't work. This includes a dead coin-battery and water damage, as well as issues with the receiver module, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not function is due to a dead battery. Modern key fobs have a limited operating range and must be within only a few feet from the vehicle to function. If you're far from your vehicle and push the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery on your coin cell (Part number CR2032) by a new one from a reputable brand such as Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store, or online.

After you've changed the battery on the coin cell, you can test it by standing near your fiat 500 keyfob 500 and pressing the buttons. The parking lights should light up and the key fob will operate the lock and unlock switch.

If the fob's remote doesn't work after replacing the battery, it might have water damage that prevents it from connecting to the receiver module inside your car. Water damage can happen in many ways, including simply splashing or submerging the key fob saltwater at the beach. If you suspect your fob was exposed to water, try placing it in a dry rice bag to draw the moisture out. If this isn't working, you'll have to get your fob reset by an auto locksmith or a dealer.

Water Damage

The fob does have rubber seals to keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater can be particularly harmful to the circuit board of the fob and can cause it to short out and eventually end up dying. It's not good to let the fob get wet however, don't give it up when you accidentally drop it in water or forget to remove it from your pants pocket.

First, remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or another similar product. Test the fob next to verify if it's working. If the key doesn't work, it may need to be reset. This is usually handled by an auto locksmith or dealer.

If the key is more recent and hasn't been programmed to your vehicle it is likely to need to be replaced completely. This is an easy process that can be handled by a professional automotive locksmith. The locksmith will need the key to be cut to match the car's ignition. They will also need to reprogram the fob for your vehicle's system. This is a cheap and quick process that could be completed within the same day.

Receiver Module Issues

The 500 key fob could stop working because it is out of range. The remote has a maximum range of 30 feet. So if you are too far away from your vehicle, it won't respond to your commands. It is possible to solve this problem by moving the remote closer to your vehicle until it responds.

If you've replaced the coin battery (commonly known as a "button" or "watch") and the fob isn't working It could be because of an internal circuit board issue. Reprogramming the fob is usually the solution to the issue. You can find the procedure for most vehicles on YouTube or in the owner's manual.

It's possible that you need to replace the metal clips that hold the coin battery. If they lose tension, it could prevent the battery from being properly seated and could cause your remote to malfunction.

In rare instances the fob might become desync'd with your vehicle because of software or hardware issues. This can cause a major issue, but you are able to usually resolve this issue by visiting a local dealer or auto locksmith to reprogram your fob for you. In certain instances the software might require reinstallation to your body control modules.

Interference

In addition to a dead battery on a coin The key fob might not be receiving or transmitting the signal due to interference. This could happen if the key fob is close to the radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob could not work because of a problem to the buttons or water damage, or damage to the internal chips.

If the key fob has stopped working one day suddenly and you've tried every option at home to resolve it e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module, which is located under the dashboard, picks up radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then translated by the vehicle.

There's a quick and easy way to reset the 500's internal system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Then, reconnect the battery. This will eliminate any remaining electricity and restart the car's computers, which could allow you to get your key fob working again. If the issue continues, you should consult an expert technician. They will be able diagnose the exact cause of any issues.