• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Change a Subaru Spare Key

If you've lost your Subaru car key, call a auto locksmith near Me. Usually, they can cut a new key for you much less expensively than the dealer.

Fob remote "push to start" intelligent keys or a plain metal key are the two main types of Subaru car keys. The Fob key comes with an embedded chip and requires reprogramming.

Keyless Entry System

The key fob can be used to lock and unlock your subaru outback key remotely. It also opens the trunk of your vehicle or the lift gate. These remotes use the keypad inside your car to connect to the computer in your vehicle.

subaru immobilizer key programming models offer a little well-known feature called PIN Code Access. You can use a customized number sequence to open and start your car. Check your owner's guide to learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

It's possible that the battery inside the key fob has gone out. You can test the battery life of your key fob using an instrument that is portable or a multimeter that you have in your garage.

The next step is to take the key fob out of its case, and then examine the circuit board that controls the transmitter. There will be one or two sets of 8 numbers. Write down the first so you remember it. Once you've done that you can put the key fob back together and you'll be able to begin programming it at home. The procedure for programming varies depending on the model and year of your car, but it's usually simple enough to do by yourself.

Key Fobs

subaru replacement key's latest models all feature key fobs that not just unlock doors and turn on your lights, lock the gas cap, and start your vehicle. This last feature is particularly helpful if you've been at the gas pump only to find that your car isn't starting because the battery for the key fob failed.

No matter if your Subaru is new or older it's likely that your key fob is able to be replaced with minimal difficulty. It's important to note that models with a high level of technological advancement may require an excursion to the dealer. But, with a bit of time and effort, you'll get your new key fob in place at home.

Start by examining the circuit board for the transmitter inside your key fob (instructions to open the case are provided in your owner's manual). It should have two or three sets of serial numbers, each of which has 8 digits long. Keep the first set of numbers on hand for future reference.

After that, get in the driver's seat and shut all doors. Turn the key ten times to start your car, then turn off the engine. Press the lock button on your key fob and then open the door to check whether your doors function properly. Then close the door, and remove the key from the ignition. You should hear the chime from your car and indicate that the key fob is programmed.

Ignition System

If your Subaru keys aren't working as they ought to, it could be because the key battery is dead. You can replace the battery in your key fob on your own if know how. Battery replacement is affordable and easy to locate. If your key fob doesn't respond to your commands, it could be a different issue. To find a spare key, you should go to a dealer. They'll ensure that the key is genuine Subaru key that's under warranty and will be programmed to your vehicle. This is more secure and less expensive than purchasing an aftermarket key from a company on the internet.

The dealer will also cut a key for you if you provide your VIN number as well as evidence of ownership. They'll utilize this information to encode the replacement key in order to be accepted by your immobilizer. This is a more complex procedure than cutting a single key, and the dealer will charge more for it.

Once the new key is programmed, you can switch it over to the working key. It takes just five seconds to insert the new key, so keep your working key close to the ready. You can take the key off after the security light has stopped flashing and test it.

Battery Replacement

One of the key features that makes Subaru fobs useful is their ability to turn on your car's power windows as well as sunroof with just a press of the button. The battery inside your Subaru fob wasn't made to last forever, and it will have to be replaced eventually. This short guide from Capitol subaru key fobs will help you to change the battery yourself.

To start you'll need to locate the small crevice in the seam that divides the back and front of your key fob. With a small screwdriver, you can pop this seam wide to reveal a small space inside which is the battery. Insert the new battery and make sure it is facing up correctly. Remove the old one. Once everything is put together and in place, you can use your new key fob to lock, unlock, and start your vehicle easily!

Always have a spare set of keys, especially if one is damaged or lost. You can purchase a replacement key at your local dealership or get it cut by locksmiths. Either way, it's important to get your key fob working correctly as soon as you can to allow you to drive in a safe manner!